KitGuru KitGuru.net – Tech News | Hardware News | Hardware Reviews | IOS | Mobile | Gaming | Graphics Cards
Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 Watt DC load.
We test ambient temperatures at 35C in our environment to greater reflect warmer internal chassis conditions.
We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• Extech digital sound level meter
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA
|
DC Output Load Regulation
|
||||||||||
|
Combined DC Load |
+3.3V
|
+5V
|
+12V
|
+5VSB
|
-12V | |||||
|
A
|
V
|
A
|
V
|
A
|
V
|
A
|
V
|
A | V | |
|
120W
|
0.90
|
3.34
|
0.93
|
5.01
|
8.95
|
12.04
|
0.50
|
5.01
|
0.20
|
-12.00
|
|
240W
|
1.62
|
3.34
|
1.63
|
5.01
|
18.45
|
12.04
|
1.00
|
5.01
|
0.20
|
-12.01
|
| 600W |
3.00
|
3.34
|
3.11
|
5.01
|
46.78
|
12.03
|
1.50
|
5.00
|
0.30
|
-12.01
|
| 900W |
4.01
|
3.34
|
4.05
|
5.01
|
70.86
|
12.02
|
2.00
|
5.01
|
0.30
|
-12.00
|
|
1200W
|
5.02
|
3.34
|
5.20
|
5.01
|
94.57
|
12.01
|
2.50
|
5.01
|
0.30
|
-12.01
|
Load regulation is very good across the board.
Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.
| Cross Load Testing | +3.3V | +5V | +12V | -12V | +5VSB | |||||
| A | V | A | V | A | V | A | V | A | V | |
| 1190W | 4.0 | 3.34 | 3.0 | 5.01 | 88.0 | 12.01 | 0.2 | -12.01 | 0.50 | 5.01 |
| 240W | 19.0 | 3.33 | 22.0 | 5.00 | 2.5 | 12.04 | 0.2 | -12.00 | 0.50 | 5.01 |
The YS1200 handled our cross load tests without any issues. When hit with 88A, the +12V rail held at 12.01.
We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum. ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.
|
ATX12V Ver 2.2 Noise/Ripple Tolerance
|
|
|
Output
|
Ripple (mV p-p)
|
|
+3.3V
|
50
|
|
+5V
|
50
|
|
+12V1
|
120
|
|
+12V2
|
120
|
|
-12V
|
120
|
|
+5VSB
|
50
|
Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the unit complied with the ATX standard.
| AC Ripple (mV p-p) | ||||
| DC Load | +3.3V | +5V | +12V | 5VSB |
| 100W | 14 | 12 | 13 | 19 |
| 200W | 17 | 13 | 17 | 22 |
| 400W | 19 | 16 | 19 | 25 |
| 600W | 21 | 18 | 20 | 27 |
| 800W | 23 | 18 | 22 | 32 |
| 1000W | 25 | 19 | 27 | 38 |
| 1200W | 26 | 22 | 32 | 42 |
Ripple suppression from the unit is pretty good overall, falling well within industry rated parameters. At full load the +12V rail peak at around 32mV. The 5VSB is a little higher at the higher power levels than I would have expected, but it is still within tolerance levels.
|
Efficiency (%)
|
|
|
100W
|
90.5
|
|
200W
|
92.7
|
|
400W
|
93.1
|
|
600W
|
93.5
|
|
800W
|
93.1
|
| 1000W | 92.4 |
| 1200W | 91.3 |
Efficiency is extremely high overall, hitting 93.5% at peak. This drops to just under 91% at full load. An excellent set of results for this power supply.
We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.
Today to test the power supply we have taken it into our acoustics room environment and have set our SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa) one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.
As this can be a little confusing for people, here are various dBa ratings with real world situations to help describe the various levels.
KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refrigerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum
|
Noise (dBA)
|
|
|
100W
|
<28.0
|
|
200W
|
<28.0
|
|
400W
|
<28.0
|
|
600W
|
31.3
|
| 800W | 34.5 |
| 1000W | 37.2 |
| 1200W | 38.1 |
This is a quality FDB fan and up until around 800 watts load it is very quiet. Once you get close to a 1000 watt power draw demand, the fan starts spinning up and is clearly audible. At full load you can clearly hear the fan but this is not a realistic power rating to be running on a regular basis.
|
Temperature (c)
|
||
|
Intake
|
Exhaust
|
|
|
100W
|
35
|
38
|
|
200W
|
36
|
41
|
|
400W
|
38
|
44
|
|
650W
|
43
|
47
|
|
800W
|
45
|
54
|
| 1000W | 47 | 57 |
| 1200W | 50 | 62 |
Temperatures are well maintained throughout the load range thanks to the high levels of efficiency of the design and the excellent fluid dynamic bearing fan in place.
